Autopapyrus · Tesla Model X (2019)
https://autopapyrus.com/catalog/tesla/model-x/guides/checking-and-replacing-the-brake-fluid/
https://autopapyrus.com/catalog/tesla/model-x/guides/checking-and-replacing-the-brake-fluid/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Tesla Model X (2019): Checking and Replacing the Brake Fluid
Tesla's schedule calls for checking the brake fluid on the Model X every 4 years and replacing it if the check shows it is needed. If you tow often, drive down long mountain grades or drive aggressively, check and replace it more often, especially in hot, humid areas. The brake system with ESP can only be bled using diagnostic software in service mode. The usual "pump the pedal with a helper" method won't work. This guide covers a full fluid replacement, bleeding all four calipers.
Key figures
- Pressure bleeder pressure30 psi. Set this on the tool before bleeding (step 7)
- Bleeder valve torque18 N·m (13 lb-ft). Use a torque wrench after each valve (steps 14-18). Overtightening can strip the valve
- Fluid checkevery 4 years. After the check, replace the fluid if it is in poor condition (step 1)
Check these values against the manufacturer’s specification for your vehicle before you start.
Part
| № | Part |
|---|---|
| 01 | Brake fluid, DOT (for Tesla)about 1-1.5 L (1.1-1.6 qt) for a full replacement, fresh from a sealed containerFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
8- Lift or jack with jack stands Amazon →
- lug wrench Amazon →
- pressure brake bleeder (for example, Power Probe Brake Bleeder 4.0) with an adapter for the Model X reservoir Amazon →
- clear drain container with hose Amazon →
- wrench for the bleeder valves (check the size on your caliper's valve) Amazon →
- 18 N·m (13 lb-ft) torque wrench Amazon →
- laptop with Tesla Toolbox 3 diagnostic software and service mode access Amazon →
- clean rags and water Amazon →
Step by step
28 steps · 4 stagesStage 1 of 4 Inspection and preparation 7 steps
- Check the condition of the fluid. The level should be between the MIN and MAX marks on the reservoir, and the fluid should be light in color. Dark or cloudy fluid, or fluid more than 4 years old, is a reason to replace it. A red BRAKE indicator on the instrument panel means the level has dropped. In that case, don't keep driving. Look for the cause of the leak instead of just topping off the fluid.
- Don't top off the reservoir "by eye" instead of replacing the fluid. A drop in level usually points to worn brake pads or a leak.
- Get your kit ready: new fluid, the pressure bleeder with the reservoir adapter, the drain container, and the laptop with Toolbox 3. Pour the new fluid from the sealed container into the pressure bleeder's tank.
- Raise the car on a lift, or set it on jack stands at the factory lifting points.
- Open the hood and remove the center lower cover of the front compartment (the under-hood panel in the middle).
- Thoroughly clean the area around the reservoir cap, then remove the cap. If the level is low, top off to the MAX mark.
- Attach the pressure bleeder to the reservoir through the adapter and set the pressure to 30 psi (about 2 bar).
Stage 2 of 4 Wheel removal and access 4 steps
- Remove all four wheels.
- Lower the car to a comfortable working height.
- Remove the two bleeder valve caps (outer and inner) from each caliper. Don't forget to put them back before reassembly.
- Make sure the car's high-voltage system is on (bleeding runs with the hydraulic unit working), connect the laptop with Toolbox 3 to the car, and unlock the car's gateway. These steps require Tesla diagnostic access.
Stage 3 of 4 Bleeding the calipers 8 steps
- Front left caliper: put the hose with the drain container on the outer bleeder valve nipple and loosen the valve.
- In Toolbox 3, open the Actions tab, find "Brake-Bleed", select PROC_ESP_FRONT-L-REAR-R_BRAKE-BLEED (in service mode: Chassis > Brakes > Brake Bleed FL-RR) and run it. Wait for it to finish.
- Tighten the outer valve to 18 N·m (13 lb-ft).
- Repeat steps 12-14 for the inner valve of the front left caliper.
- Front right caliper: do the same with the outer valve, then the inner valve, but run PROC_ESP_FRONT-R-REAR-L_BRAKE-BLEED (Chassis > Brakes > Brake Bleed FR-RL). Tighten each valve to 18 N·m (13 lb-ft).
- Rear right caliper: same order, run PROC_ESP_FRONT-L-REAR-R_BRAKE-BLEED (Brake Bleed FL-RR). Valves: 18 N·m (13 lb-ft).
- Rear left caliper: same order, run PROC_ESP_FRONT-R-REAR-L_BRAKE-BLEED (Brake Bleed FR-RL). Valves: 18 N·m (13 lb-ft).
- Make sure the bleeder tank always has fluid and that no air gets into the hose. During bleeding, fluid without bubbles should flow into the container.
Stage 4 of 4 Finishing up and testing 9 steps
- Remove the pressure bleeder from the reservoir.
- Check the level, top off to MAX if needed, and close the cap firmly.
- In Toolbox 3, find "Pressure-Burnished" and run TEST_BRAKE_X_STIFFNESS-TEST-PRESSURE-BURNISHED (in service mode: Chassis > Brakes > Brake Stiffness Test). If the test fails, repeat the bleeding starting from step 12.
- Disconnect the laptop from the car.
- Install the bleeder valve caps on the calipers.
- Install the wheels and tighten the lug nuts in a criss-cross pattern to the Tesla specification for the Model X, then re-torque them after lowering the car.
- Reinstall the center cover of the front compartment and close the hood.
- Take a test drive on a safe stretch of road with several firm stops. The pedal should feel firm, with no sinking.
- Rinse any brake fluid splashes off the body with water and make sure there are no leaks at the calipers.
Common mistakes and warnings
- Brakes are a safety system
- If you don't have experience or the equipment for service mode, leave the job to a repair shop
- Brake fluid damages paint, so keep clean rags and water handy
- Brake fluid is toxic and absorbs moisture, so don't use an opened or old container
- If the pedal feels soft after the work and the stiffness test fails, don't drive the car on the road
How it works · 3D
How Car Brakes Work
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Tesla Brand
Tesla Motors, a North American company founded in 2003, is rightly considered the pioneer of a new era in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →