← Model X

Tesla Model X (2019): Opening the Vehicle When the Low-Voltage Battery Is Dead

When the 12 V low-voltage battery is dead, the key fob buttons, the app and the touchscreen don't work, so the doors have to be opened mechanically. Power applied to the terminals behind the tow eye cover opens the hood (front trunk) latches, but it does not charge the battery through those terminals. This guide is for a vehicle where you need mechanical access to the doors. Charging and replacing the battery are covered separately.

DifficultyMedium Time20-40 minutes Steps10

Key figures

  • Time the leads may stay connected to the terminals under the tow eye cover
    no more than 30 seconds. Once the hood pops open, remove the leads immediately (step 9)
  • Low-voltage battery "−" terminal tightening torque
    5 N·m (3.7 lb-ft). If you disconnected the terminal, tighten it with a torque wrench (step 10)

Check these values against the manufacturer’s specification for your vehicle before you start.

Part

№Part
01 12 V battery for Tesla Modelif worn, based on test resultsFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

4
  • small flat-blade screwdriver Amazon →
  • portable jump starter or other external low-voltage (12 V) power source with leads and clamps Amazon →
  • soft cloth to protect the plastic Amazon →
  • flashlight Amazon →

Step by step

10 steps
  1. Make sure the cause really is the low-voltage circuit. The touchscreen is dark, the key fob and the app don't respond, and the vehicle shows no signs of an accident. If the key fob doesn't unlock the doors and the screen won't turn on, go to step 2.
  2. Open a front door manually. Pull up the mechanical emergency release handle in front of the window switches. No electrical power is needed for this.
  3. Note that the window does not lower by itself when you open the door with the emergency handle. Open the door smoothly, without yanking it, to avoid damaging the glass and the trim. If low-voltage power is disconnected, do not open the doors with the windows raised, because the glass may break. It is better to lower the windows beforehand, while there is still power.
  4. If you need to get into the Falcon Wing rear doors, carefully remove the speaker grille on the door and pull the mechanical emergency release cable down and forward. Work without jerking, and do not damage the grille or the door trim.
  5. Prepare an external low-voltage power source. A portable jump starter will work. Make sure it is charged and switched off.
  6. Remove the tow eye cover on the front bumper. Insert a small flat-blade screwdriver into the upper and lower slots, release the clips, and pull the cover toward you. Place a cloth underneath so you don't scratch the bumper.
  7. Pull two wires out of the opening under the cover. Two terminals will be exposed.
  8. Connect the source's red lead to the red terminal marked "+". Then connect the black lead to the black terminal marked "−".
  9. Switch on the external source according to its instructions. The hood latches release immediately. Do not keep the leads connected for more than 30 seconds: as soon as the hood pops open, switch off the source and remove the leads, black ("−") first, then red ("+").
  10. Raise the hood and access the front trunk. From here you can test, charge or replace the low-voltage battery. If you disconnected and reconnected the "−" terminal, tighten it to 5 N·m (3.7 lb-ft). After power is restored, the screen may show "Calibration Needed." If so, clear the space around the rear doors and hold the CALIBRATE button on the screen until "CALIBRATION COMPLETE" appears. Stand to the side, because the doors do not react to obstacles during calibration. Then reinstall the tow eye cover: tuck the wires back inside, align the cover and snap it into place.

Common mistakes and warnings

  • Voltage at the terminals under the tow eye cover only releases the hood latches and does not charge the battery
  • Do not connect high-current chargers to these terminals, to avoid damaging the circuits
  • Do not cut the first responder loop if you disconnect the battery
  • Before disconnecting low-voltage power, lower the windows and leave at least the driver's door open
  • Otherwise the vehicle could lock with you inside or outside, and raised windows could break when a door is opened
  • If you have no experience working with vehicle electrical systems, or the battery keeps discharging, take the car to a repair shop, since the cause may be a constant parasitic drain
  • Do not touch the high-voltage battery or the orange high-voltage cables
Spotted a mistake? Tell us →

Our articles

More articles →