← Model X

Tesla Model X (2019): Cleaning and Lubricating the Brake Calipers

Cleaning and lubricating the calipers is needed if the pads wear unevenly, a caliper sticks, or you notice squealing and dragging. Most often this is caused by corrosion on the abutment surfaces. This guide covers all four calipers. The front calipers don't need to be removed. The rear calipers (with the built-in electric parking brake) are held on by two bolts. Before starting, put the parking brake into service mode through the touchscreen.

DifficultyMedium Time2-4 hoursall four wheels Steps40

Key figures

  • Lug nut torquefinal tightening with a torque wrench with the car on the floor, in a star pattern (step 36)
    175 N·m (129 lb-ft)
  • Two rear caliper bolts torqueafter installing the caliper on the bracket, with a torque wrench (step 29)
    26 N·m (19 lb-ft)
  • Rear caliper nameplate bolt torquea small bolt that is easy to strip, so tighten it with a torque wrench (step 28)
    9 N·m (80 lb-in)
  • Front caliper bolt torqueonly if the caliper was removed completely; not needed for a routine cleaning (Warning)
    135 N·m (100 lb-ft)
  • Rear caliper piston slot positionset before installing the caliper, otherwise it may not seat (step 27)
    "12 o'clock" and "6 o'clock"

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

8
№Part
01 Brake cleanerFind on Amazon →
02 High-temperature brake caliper grease (for guide pins and abutments, rubber-compatible)Find on Amazon →
03 Caliper retaining pinsif wornFind on Amazon →
04 Anti-rattle springsif wornFind on Amazon →
05 Abutment clipsif wornFind on Amazon →
06 Brake pad shims (anti-noise plates)if wornFind on Amazon →
07 Boltsif wornFind on Amazon →
08 Brake padsif wornFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

11

Step by step

40 steps · 4 stages
Stage 1 of 4 Preparation 6 steps
  1. Put on a respirator and gloves, because brake dust is harmful. Apply grease in a thin layer and only where indicated. It must not get on the rotors, the friction surface of the pads, or rubber parts.
  2. On cars with air suspension: on the screen, open Controls (car icon), then Suspension. While holding the brake pedal, tap Jack to turn on Jack Mode.
  3. Place the car on a two-post lift (or on a jack at the factory lift points, with jack stands). Loosen the lug nuts beforehand.
  4. Raise the car so the wheels are off the floor. If you are using a jack, chock the opposite wheels.
  5. On the screen, turn on service mode. Then open Vehicle Info, Chassis, Brakes and tap EPB Service Mode. In the settings, set the target to BOTH, the type to START and tap Run. This disables the electric parking brake while you work.
  6. Raise the car to working height and remove all four wheels. Before removing the lug nuts, take off the 5 decorative caps on each wheel.
Stage 2 of 4 Front calipers 12 steps
  1. For the left front caliper, turn the hub all the way to the right.
  2. Drive out the retaining pins with a punch and remove the anti-rattle spring (hold-down spring). The pins are spring-loaded, so keep a hold of them.
  3. Use the caliper spreader to push the pads apart and press the pistons back into the caliper.
  4. Remove the pads and keep them separate. The inner and outer pads must go back in their original positions, because they have worn in to those positions.
  5. Remove the spring plate (shim) from each pad. It is held on by clips. Wipe the shims and the pad backing plates with a rag.
  6. Use a brush and brake cleaner to clean the caliper abutment surfaces, the piston ends, the inside surfaces of the caliper, the retaining pins, the anti-rattle spring, the shims and the pad edges. Let everything dry. Keep the pad friction material clean.
  7. If the abutment surfaces are corroded, work from gentle to aggressive: nylon brush first, then wire brush, then brake file (3-4 firm strokes in one direction, without removing the coating or the metal). Replace rusted pins, springs, shims and bolts.
  8. Apply a thin layer of grease to the caliper abutment surfaces and between the two plates that attach to the back of each pad. Do not lubricate rubber parts or the piston seals.
  9. Fit the shims onto the pad backing plates. Apply a thin layer of grease to the pad edges that sit on the abutment surfaces. Do not lubricate the backing plates or the friction surfaces.
  10. Install the pads (inner and outer in their own positions), fit the anti-rattle spring and drive in the retaining pins with the punch.
  11. Rotate the rotor 180 degrees and clean grease and dirt off it with brake cleaner. Repeat.
  12. Turn the hub all the way to the left and repeat steps 8-17 on the right front caliper. Then return the wheels to the straight-ahead position.
Stage 3 of 4 Rear calipers 14 steps
  1. For the left rear caliper, clean dirt off the caliper connector and the wiring harness, then press the red lock and disconnect the connector.
  2. Slide the caliper outward to partially push back the piston.
  3. Remove the two bolts that hold the caliper to the bracket and take the caliper off. Hang it on an S-hook. Do not twist or stretch the hose, or you may damage it.
  4. Remove the bolt and take off the caliper nameplate (tag).
  5. Use the spreader to press the piston fully back into the caliper.
  6. Remove the pads from the bracket, keeping the inner and outer pads separate. Remove the abutment shims from the bracket.
  7. Use a brush and brake cleaner to clean the abutment surfaces, the piston ends, the inside surfaces of the caliper and bracket, the abutment shims and the pad edges. Keep the friction material clean. Replace rusted parts (replace the caliper-to-bracket bolts if the heads are deformed).
  8. Install the abutment shims in the bracket, then the pads in their own positions.
  9. Set the caliper piston slots at the "12 o'clock" and "6 o'clock" positions.
  10. Install the nameplate and tighten its bolt to 9 N·m (80 lb-in).
  11. Install the caliper on the bracket and tighten the two mounting bolts to 26 N·m (19 lb-ft).
  12. Connect the connector, snap the red lock closed and check the connection: pull, push, pull.
  13. Rotate the left rear rotor 180 degrees and clean grease and dirt off it with brake cleaner. Repeat.
  14. Repeat steps 19-31 on the right rear caliper.
Stage 4 of 4 Reassembly and check 8 steps
  1. Install all four wheels. Thread the lug nuts on by hand in a crisscross pattern, then tighten them with a wrench in a star pattern.
  2. Lower the car so the wheels just touch the floor. There should be no load on the wheels.
  3. On the screen, press and hold Park to turn off the parking brake service mode. Then turn off the vehicle's service mode.
  4. Lower the car all the way and give the lug nuts of all wheels their final tightening to 175 N·m (129 lb-ft) in a star pattern. Install the lug nut caps.
  5. Press the brake pedal until it feels firm (the pads are seating).
  6. In regions where roads are salted, rinse the suspension at each wheel with water.
  7. On cars with air suspension: on the screen, select Suspension, hold the brake pedal and tap Standard (this turns off Jack Mode). Drive the car off the lift.
  8. Carefully drive a short loop and brake firmly several times. This dries the pads and rotors and lets you check braking. There should be no squealing, pulling to one side or vibration.

Common mistakes and warnings

  • Brakes are a safety system
  • If you have no experience working on brakes, have a repair shop do the job
  • Do not let grease get on the rotors or pads: stopping distance will increase sharply
  • Never leave a caliper hanging by its hose and never twist the hose
  • Service mode for the parking brake is mandatory: without it, the rear calipers must not be removed and the pistons must not be pushed back
  • The car is electric: brake work does not involve the high-voltage circuit, but stay out of the under-hood and powertrain components
  • If you remove a front caliper completely or disconnect a hose, the brakes will need to be bled, and the front caliper-to-knuckle bolts are tightened to 135 N·m (100 lb-ft)
How it works · 3D How Car Brakes Work How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →

Our articles

More articles →