← Model X

Tesla Model X (2019): Jacking Up and Rotating the Wheels

On a Model X with air suspension, you must turn on Jack Mode before lifting. Otherwise, the suspension will try to self-level and may damage the vehicle or injure someone. Lift the vehicle only at the four approved points on the structural side sills of the body, and never under the battery pack. This guide covers lifting with a jack and rotating the wheels. The front and rear wheels on the Model X have different widths (for example, 9.0 and 10.0 inches on 20-inch wheels), so you can only swap them between the left and right sides of the same axle. Directional tires must stay on their own side.

DifficultyMedium Time45-60 minutes Steps25

Key figures

  • Lug nut tightening torque
    175 N·m (129 lb-ft). Set it on the torque wrench in step 21, after the tire has touched the floor. Loose nuts are dangerous, because the wheel can come off.
  • Speed at which Jack Mode turns off by itself
    above 7 km/h (4 mph). Turn the mode on before lifting (steps 5-6) and turn it off after the work (step 23).
  • Mileage for rechecking the nuts
    50-100 km (30-60 miles). Tighten the nuts with a wrench once more (step 25).

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

3
№Part
01 Rubber or polyurethane jack point pads (adapters)if needed; not foamFind on Amazon →
02 Hub centering ringsif neededFind on Amazon →
03 Lug nut capsif neededFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

7

Step by step

25 steps · 6 stages
Stage 1 of 6 Preparation 4 steps
  1. Park the vehicle on a level, firm surface and shift into P (Park). Close the hood, the trunk, and all doors, including the rear Falcon Wing doors.
  2. Unplug the charging cable. Do not lift the vehicle with the cable connected, even if it is not charging.
  3. Check that the floor jack and jack stands are in good condition: no oil leaks, no cracks, and flat support surfaces.
  4. Fit the jack point adapter on the jack. Per Tesla's guidelines, its pin must fit into the hole in the jack point.
Stage 2 of 6 Jack mode and lifting preparation 4 steps
  1. Wake the screen and press the brake pedal. In the Controls menu, open Suspension and select the highest ride height (Very High).
  2. Then go to Controls, Service, and turn on Jack Mode. A message should appear in the instrument cluster saying the active suspension is disabled. The mode resets on its own when the speed exceeds 7 km/h (4 mph).
  3. Loosen the lug nuts on the wheels you will remove by about half a turn. Do this while the wheel is still on the ground. Use a 21 mm socket.
  4. Place wheel chocks under the wheel diagonally opposite the corner you are lifting. If you are lifting the left front, chock the right rear.
Stage 3 of 6 Jacking up the vehicle 6 steps
  1. Find the approved jack point on the structural side sill of the body. There are four: in front of each rear wheel and behind each front wheel. Find the exact location by the marks on the sill and in the illustration in the owner's manual. Do not use any other locations or the area under the battery pack. Damage from this is not covered by the warranty.
  2. Position the jack with the adapter under the point and align the adapter pin with the hole.
  3. Raise the vehicle until a jack stand can fit under it. Place the jack stand under the adapter, lining up the stand's cutout with the jack.
  4. Slowly lower the jack onto the jack stand and move the jack out of the work area.
  5. Never support the vehicle at diagonal points at the same time (for example, left front and right rear). To rotate the wheels, lift one whole axle: first one corner and its jack stand, then the other corner of the same axle and the second jack stand.
  6. Push on the vehicle body to check that it is stable. Never work under a vehicle that is supported only by a jack.
Stage 4 of 6 Removing and rotating the wheels 3 steps
  1. Fully unscrew the lug nuts and remove the wheel. Hold it as you do, because it is heavy. Remove both wheels on the axle.
  2. Inspect the tires and wheels (cuts, bulges, tread wear). Wipe the hub and wheel mounting surfaces clean of dirt and corrosion.
  3. Swap the wheels only within the same axle: left to the right side and vice versa. If the tires are directional (arrow on the sidewall), put the wheels back on their original sides without swapping. Do not move wheels from the front axle to the rear.
Stage 5 of 6 Installation and tightening 5 steps
  1. Fit the wheel onto the hub, aligning the holes, and thread all the lug nuts on by hand.
  2. Snug the nuts in a crisscross (star) pattern, using an impact wrench on low torque or a wrench.
  3. Raise the vehicle with the jack off the jack stand, remove the stand, and lower the vehicle until the tire touches the floor and the suspension starts to take load.
  4. Tighten the nuts in a crisscross pattern with a torque wrench to 175 N·m (129 lb-ft). Watch the units: setting 129 N·m instead of 129 lb-ft leaves the nuts badly under-tightened. Do not use an impact wrench for final tightening.
  5. Lower the vehicle fully, remove the jack and chocks, and check that no tools are left under the vehicle.
Stage 6 of 6 Finishing up and checking 3 steps
  1. Turn off Jack Mode the same way: Controls, Service, Jack Mode. The suspension will return to normal mode (it also turns off by itself above 7 km/h (4 mph)).
  2. Check the tire pressure against the placard on the door pillar and make sure there are no pressure warnings on the screen.
  3. After driving 50-100 km (30-60 miles), recheck the lug nut torque with a torque wrench.

Common mistakes and warnings

  • If you do not disable the air suspension with Jack Mode, the vehicle may try to self-level during lifting, which is dangerous to your health and will cause damage
  • Lift the vehicle only at the four approved points on the side sills, not under the battery pack
  • Do not work under a vehicle that is held up only by a jack
  • If you have no experience with jacks and jack stands, leave the job to a tire shop or repair shop
Spotted a mistake? Tell us →

Our articles

More articles →