Autopapyrus · Tesla Model X (2019)
https://autopapyrus.com/catalog/tesla/model-x/guides/front-brake-pad-replacement/
https://autopapyrus.com/catalog/tesla/model-x/guides/front-brake-pad-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Tesla Model X (2019): Front Brake Pad Replacement
This guide covers the front pads. On a 2019 vehicle (first-generation Model X, 2015-2020), the caliper is attached to the steering knuckle with two 18 mm bolts, and the pads are held by two pins with a spring clip. The pads can be replaced without removing the caliper: you only need to knock out the pins. The rear pads are replaced using a different procedure.
Key figures
- Caliper bolt torque120 N·m (89 lb-ft), torque wrench with 18 mm socket, steps 16 and 17; these bolts hold the entire caliper
- Wheel lug nut torque175 N·m (129 lb-ft), 21 mm socket, step 19; tighten only after lowering the vehicle onto its wheels
- Rotor retaining bolt torque17 N·m (13 lb-ft), Torx T45 bit, step 15; the bolt is single-use, so install a new one
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
5| № | Part | Alternatives |
|---|---|---|
| 01 | Front brake pads, Tesla Modelaxle set, 2 pads per sideFind on Amazon → | AlternativesBremboTextarAkebono |
| 02 | Spring anti-rattle clips and pad pinsif corroded or damagedFind on Amazon → | |
| 03 | Brake rotor retaining bolt with patch coatingif removing the rotorFind on Amazon → | |
| 04 | Brake cleanerFind on Amazon → | |
| 05 | Silaramic greaseFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
10Step by step
24 steps · 6 stagesStage 1 of 6 Preparation and lifting 4 steps
- Turn the vehicle off and open the left front door. On the screen, select Controls > Service > Jack Mode. This keeps the air suspension from lowering and damaging the lift points.
- Raise the vehicle with a lift or jack, using only the factory lift points, and set it on jack stands.
- Loosen and remove the front wheels (21 mm lug nuts). Check that the lug nut threads are clean before reinstalling.
- Turn the steering wheel all the way to the right to open up access to the left caliper.
Stage 2 of 6 Removing the old pads 4 steps
- Remove the pins and the spring anti-rattle clip from the caliper. Hold the spring down while driving out the pin, and remove the upper pin first. Seized pins can be knocked out with an air hammer or a punch.
- Push the caliper pistons back: press on the inner and outer pads. If you use pliers, wrap the caliper in a rag so you don't scratch it.
- Remove both pads. If the pads are stuck, pry them out with a pad puller or use an air hammer.
- Inspect the rotor. Deep grooves, a lip at the edge or heavy wear are reasons to replace the rotors (see steps 14-16).
Stage 3 of 6 Cleaning and installing new pads 5 steps
- Clean the pad guides on the caliper and the pistons with a brush and brake cleaner. On a painted caliper, use a nylon brush and let the cleaner dry. If corrosion is severe, replace the caliper.
- Apply Silaramic grease to the guide slots on both pads. Apply it only to the metal backing plate. No grease should get on the friction material. If it does, wipe it off with brake cleaner.
- Clean the pins and the spring clip. Replace any that are corroded or deformed.
- Install the inner and outer pads in the caliper.
- Install the spring clip and pins, lower pin first, then the upper pin. Make sure both pins are fully seated.
Stage 4 of 6 Rotor replacement (only if needed) 3 steps
- Remove the two caliper bolts (18 mm) and hang the caliper from an S-hook on the body or suspension. Do not twist the caliper or let it put load on the brake hose.
- Remove the rotor retaining bolt (Torx T45; it is a single-use patch-coated bolt, so discard it) and take off the rotor. Install the new rotor, aligning the hole, and tighten the new bolt to 17 N·m (13 lb-ft).
- Take the caliper off the hook, set it on the steering knuckle and tighten the two bolts (18 mm) to 120 N·m (89 lb-ft).
Stage 5 of 6 Right side and reassembly 4 steps
- Turn the steering wheel all the way to the left and repeat steps 5-16 on the right side.
- Install the wheels. Thread the lug nuts on by hand first, then tighten them in stages in a crisscross pattern.
- Lower the vehicle onto its wheels and tighten the lug nuts (21 mm) to 175 N·m (129 lb-ft). Install the decorative lug nut caps (5 per wheel).
- Lower the lift arms completely and turn off Jack Mode on the screen.
Stage 6 of 6 Check and break-in 4 steps
- Before driving, press the brake pedal several times until it feels firm. This seats the pads against the rotors.
- If the pedal is soft or sinks to the floor, that indicates air in the system, and the entire brake system will need to be bled.
- Break in (bed in) the new pads using the Tesla procedure: a series of moderate stops on a safe, empty stretch of road. For the first 100-200 km, avoid hard braking unless necessary.
- Test the brakes at low speed and listen for unusual noises. After 50-100 km, check the wheel nut torque.
Common mistakes and warnings
- Brakes are a safety system
- If you have no experience working on brakes, have the job done at a repair shop
- Never work under a vehicle supported only by a jack
- Do not inhale brake dust or blow it off with compressed air
- Be sure to enable Jack Mode, otherwise the air suspension may lower the vehicle
- The electric parking brake is not involved with the front pads. 2021 and newer vehicles (Palladium) use different caliper mounting bolts (21 mm, 135 N·m (100 lb-ft)): do not mix up the torque values
How it works · 3D
How Car Brakes Work
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Tesla Brand
Tesla Motors, a North American company founded in 2003, is rightly considered the pioneer of a new era in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →