← Model X

Tesla Model X (2019): Replacing the Low-Voltage (12 V) Battery

The low-voltage battery is located in the front trunk (frunk) under the panels, behind the HEPA filter housing and inside a metal cage. To reach it, you only need to remove the HEPA filter. Then disconnect the 12 V power, detach the cage, and take out the battery. After disconnecting 12 V, you must calibrate the Falcon rear doors. This job does not require disconnecting the high-voltage system, but work carefully: wiring harnesses and the first responder loop run nearby.

DifficultyMedium Time1-1.5 hours Steps26

Key figures

  • New battery voltage before installation
    above 12.6 V. Measure with a multimeter. From 12.4 to 12.6 V it needs charging, and below 12.4 V do not install it (step 1)
  • Negative and positive terminal torque
    5 N·m (3.7 lb-ft). 10 mm wrench with a torque wrench. Too loose and the terminal wobbles, too tight and the thread strips (steps 9, 21, 22)
  • Lower battery cage bolt torque
    6 N·m (4.4 lb-ft). 10 mm socket (steps 15, 20)
  • Upper battery cage bolt torque
    15 N·m (11 lb-ft). 13 mm socket (steps 16, 20)
  • Battery hold-down bar nut torque
    4 N·m (3 lb-ft). 10 mm socket (steps 18, 19)
  • Wait after disconnecting power
    at least 2 minutes, until the circuits discharge (step 11)

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

3
№PartAlternatives
01 12 V lead-acid battery with a vent hole and plug on the positive terminal sideFind on Amazon → AlternativesBoschVartaExide
02 Disposable HEPA filterin case of damage during removalFind on Amazon →
03 Sealsin case of damage during removalFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

9

Step by step

26 steps · 5 stages
Stage 1 of 5 Preparation 6 steps
  1. Check the new battery with a multimeter. An open-circuit voltage above 12.6 V is good. From 12.4 to 12.6 V, charge it first. Below 12.4 V, do not install it. Reject that battery.
  2. Make sure the old battery is not overheated (no strong heat or swelling). If it is hot, wait and do not work on it.
  3. Open all the doors and lids you may need: with 12 V disconnected, the rear doors and the liftgate will not work.
  4. If the vehicle is charging, unplug the charging cable. Set the vehicle to Park.
  5. Open the front trunk. On the touchscreen, turn off climate control and wait at least 30 seconds.
  6. Lower the windows of all doors completely, especially the driver's window. With 12 V disconnected, do not try to open a front door while its window is up. The glass may break, and with the driver's window up, the vehicle may lock you in.
Stage 2 of 5 Access and disconnecting 12 v 5 steps
  1. Remove the HEPA filter housing and filter (this is the only part you need to remove for access).
  2. Open the driver's door. On the screen, go to: Controls, Parking Brake & Power Off, Power Off.
  3. Disconnect the negative battery terminal (10 mm wrench).
  4. Disconnect the first responder loop. Do not cut it.
  5. Wait at least 2 minutes for the electrical circuits to fully discharge.
Stage 3 of 5 Battery removal 7 steps
  1. Remove the red plastic cap from the positive terminal and disconnect the positive clamp (10 mm wrench).
  2. Release the clips that hold the 12 V harnesses to the top of the battery cage, and the coolant hose clip at the bottom of the cage.
  3. Carefully remove the vent tube from the battery.
  4. Remove the 2 lower cage bolts with the plastic beam (10 mm socket).
  5. Remove the 2 upper cage bolts with the crossmember (13 mm socket).
  6. Lift the lower part of the cage and slide the assembly forward, without damaging or pinching the wiring.
  7. Remove the hold-down bar nut (10 mm socket), take off the bar, and lift the battery straight up and out.
Stage 4 of 5 Installation 4 steps
  1. Make sure the vent hole on the positive side of the new battery has a plug in it. Place the battery in the cage, install the hold-down bar, and tighten the nut to 4 N·m (3 lb-ft).
  2. Put the cage back in place. Tighten the 2 lower bolts to 6 N·m (4.4 lb-ft) and the 2 upper bolts to 15 N·m (11 lb-ft). Connect the vent tube and secure the harness and hose clips.
  3. Connect the positive clamp, tighten it to 5 N·m (3.7 lb-ft), and put the red cap back on.
  4. Connect the first responder loop and the negative terminal (5 N·m (3.7 lb-ft)).
Stage 5 of 5 Check and calibration 4 steps
  1. Clear the area around the rear doors and do not stand near them. During calibration, the safety sensors are disabled, so the doors will not stop for an obstacle.
  2. After power is restored, a "Calibration Required" message will appear on the screen. Press and hold the CALIBRATE button until "CALIBRATION COMPLETE" appears (the lower doors open fully, the upper doors lower, then the lower doors close, in under a minute). Keep holding the button for another 5 seconds after it finishes.
  3. Reinstall the HEPA filter and its housing. Raise the windows, then close the doors and the front trunk.
  4. Check that the screen, windows, doors and charge port work and that there are no errors on the display. If the vehicle does not power on, supply power from an external 12 V source for a few minutes.

Common mistakes and warnings

  • With 12 V disconnected, the windows and doors behave unusually, so do not skip steps 3 and 6
  • Do not cut the first responder loop
  • Do not touch the high-voltage components (orange cables)
  • Without training and 1000 V rated gloves, this is life-threatening
  • If you have no experience working on a vehicle's electrical system, have a repair shop do the replacement
  • The old battery contains acid and lead
  • Recycle it at a collection point
Spotted a mistake? Tell us →

Our articles

More articles →