← Model X

Tesla Model X (2019): Tire Pressure Monitoring Sensor (TPMS) Replacement

The sensor is mounted to the wheel rim on the inside of the tire, so replacing it requires removing the wheel and dismounting the tire from the rim, which means you need a tire changer. After installing the new sensor, you must have the control unit relearn the sensor IDs, then drive for a few minutes. This guide covers replacing one sensor; the procedure is the same on the other wheels.

DifficultyMedium Time1-1.5 hours per wheelincluding balancing Steps22

Key figures

  • Sensor nut torque on the rim
    8 N·m (71 lb-in), 11 mm socket with a low-range torque wrench, step 13; do not overtighten, as you can damage the sensor or the threads
  • Upper roller position on the changer
    about 100 mm in front of the valve stem, to avoid hitting the sensor while breaking the beads, step 6
  • Speed at which the sensors start transmitting pressure
    about 8 km/h (5 mph), check from this speed that readings appear on the screen after erasing the IDs, step 21

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

3
№PartAlternatives
01 TPMS sensor for Model X before 2021, non-Bluetooth, with mounting nut and sealFind on Amazon → AlternativesTeslaAutelSchrader
02 Valve coreFind on Amazon →
03 Stick-on wheel balancing weightsFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

12

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

Step by step

22 steps · 5 stages
Stage 1 of 5 Preparation 3 steps
  1. Identify which wheel has the faulty sensor (the TPMS indicator is on or flashing, or the screen shows no pressure for one wheel). Buy a sensor that fits vehicles built before 2021 (non-Bluetooth).
  2. Park the vehicle on level ground, apply the parking brake, and power the vehicle off. Loosen the lug nuts 1/2 turn, then lift the vehicle at the designated jacking points.
  3. Remove the wheel. Lug nut torque for installation is per the manufacturer's specification (for the Model X, the reference is 170-180 N·m (125-133 lb-ft); verify the exact value against Tesla data).
Stage 2 of 5 Tire dismounting 6 steps
  1. Put on safety glasses and gloves. Remove the valve core with the valve core tool and release all the air. Pressure escapes from the tire quickly.
  2. Place the wheel face up on the tire changer, install the center clamp and cone, and tighten the cone.
  3. Rotate the wheel so the upper roller is about 100 mm in front of the valve stem. This keeps it from hitting the sensor.
  4. While rotating the wheel, break the upper and lower tire beads, lubricating the beads generously with tire mounting paste.
  5. Position the changer's working head at the edge of the rim, hook the upper bead with the tire lever, and pull it over the rim. Make sure the head and lever do not touch the sensor.
  6. Lift the tire and repeat for the lower bead, then remove the tire from the rim.
Stage 3 of 5 Sensor replacement 4 steps
  1. Use the 11 mm socket to remove the nut that secures the sensor to the rim, then remove the sensor.
  2. On the new sensor, remove the valve cap and unscrew the nut.
  3. Wipe the sensor mounting hole inside and out with an alcohol wipe. Make sure the seal on the sensor base is fully seated.
  4. Install the sensor so it sits snugly against the rim, then tighten the nut to 8 N·m (71 lb-in).
Stage 4 of 5 Tire mounting and balancing 5 steps
  1. Lubricate both beads. Check the rotation direction and the "outside" marking on the tire sidewall.
  2. Mount the lower bead first, then the upper bead. Position the sensor in front of the changer's working head so the head does not damage it as the wheel rotates.
  3. Inflate the tire until the beads seat, without exceeding the pressure marked on the sidewall. Install the valve core and bring the pressure to the value on the "Tire and Loading Information" placard on the driver's side door pillar.
  4. Place the wheel on the balancer. Remove all old weights with the plastic scraper, clean off any adhesive residue, and wipe the rim.
  5. Enter the vehicle and wheel data and balance the wheel: apply new weights along the red laser line and verify with a second spin. Install the valve cap.
Stage 5 of 5 Installation and sensor relearn 4 steps
  1. Mount the wheel on the hub, tighten the lug nuts in a crisscross pattern, lower the vehicle, and tighten the lug nuts to the specified torque.
  2. Using Service Mode (Chassis, then TPMS, then Erase All TPMS IDs) or Toolbox, erase the stored sensor IDs. This action deletes all stored IDs.
  3. Drive a short distance: the sensors begin transmitting at about 8 km/h (5 mph). Confirm that the pressure for all four wheels appears on the screen. If any wheel is not displayed, repeat the sensor scan and drive again.
  4. Compare the readings with a tire pressure gauge and, if necessary, adjust the pressure to the value on the door pillar placard.

Common mistakes and warnings

  • Air escapes from the tire quickly once the valve core is removed, so wear safety glasses and gloves
  • Do not exceed the pressure marked on the tire sidewall
  • If you don't have a tire changer and experience, have a tire shop dismount the tire: you could damage the sensor, the bead, or the rim
  • Tightening the lug nuts is a safety-critical operation, so use a torque wrench
Spotted a mistake? Tell us →

Our articles

More articles →